POWER PACKAGE: JLT BIG AIR / SCT Tuner / PULLEY (07-09 GT500)

$719.00

(1 review) Write a Review
SKU:
CAIP-GT500-07-X4
Shipping:
Free Shipping
CARB Status:
NOT CARB EXEMPT
Computer Tuning Required:
YES
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
POWER PACKAGE: JLT BIG AIR / SCT Tuner  / PULLEY (07-09 GT500)

Package includes JLT Big Air Intake Kit, SCT X-4 Power Flash Tuner loaded with Custom Tunes, JLT T-Shirt, and Free Standard shipping to Continental US.
PULLEY PACKAGE OPTIONAL

INTAKE:
BIG AIR PLASTIC INTAKE TUBE WITH MOLDED IN MAF
The best part of our Big Air intake is we kicked the cool factor up a notch and molded a 123mm MAF housing right in the tube. With no separate MAF housing or couplers air flow is fast and smooth.. Early testing shows this can be used with the stock MAF sensor all the way up to 750 RWHP and well beyond with a MAFia, SCT BA5000 or HPX sensor.

HEAT SHIELD
Includes our new roto molded heat shield to block engine heat at idle and low speed. It has two mounting points and a weather strip that seals to the hood and uses a large area to make sure the filter has tons of cool air.

GAINS (INTAKE & TUNE)
60-90 RWHP is typical with this kit and our custom tune. This puts most GT500’s at 495-515 HP at the rear tires. (500 HP is rated at the flywheel from the factory)

GAINS (INTAKE/PULLEY/TUNE)
100-130 RWHP is typical with this kit and our custom tune. This puts most GT500’s at 525-540 HP at the rear tires. (500 HP is rated at the flywheel from the factory)

TUNER:
Click here for SCT X-4 Tuner details

TUNING:
The tuner will come preloaded tuned for your mods, the tune is scaled appropriately for the 2.6 Supercharger pulley. Therefore if you add the pulley at a later date, no tune adjustments will need to be made. This will allow you to add the parts in stages if you choose to. 

OPTIONAL PULLEY PACKAGE
Includes 2.6 (4 PSI over stock) METCO Interchangeable Supercharger Pulley (MSP-2.6), METCO Auxiliary Double Bearing Idler Kit (MSI-90D)
SPARK PLUGS: Includes (8) NGK TR6 Spark Plugs. *WE RECOMMEND YOU CHANGE YOUR SPARK PLUGS WHEN CHANGING YOUR SUPERCHARGER PULLEY. NGK-TR6 PLUGS SHOULD BE GAPPED AT .035**

*Please note, a Pulley Puller Tool is required for installation. You have the option to add the METCO Pulley Puller and Installation Tool to your order for $119.00 ($20.99 off retail).

Please be sure to carefully make all required selections below. 

EASY INSTALL
The new design, detailed instructions and online video instructions helps make this an easy install (see Instructions & Videos tabs to download / view).

KIT INCLUDES:

  • JLT Rotomolded Intake Tube 
  • Silicone Coupler
  • 5x7 S&B Powerstack Air Filter
  • Rotomolded Heat Shield
  • HD Clamps & all needed hardware
  • SCT X-4 tuner
  • Optional pulley package

AIR FILTER: OIL OR DRY
We use only the best air filters made by S&B to our specifications.
For years we only used oiled filters, but dry filter technology has been proven and is now a popular option.

Should I choose a Dry Disposable or Cotton Oiled Filter?
Since you are not sacrificing performance with either choice, the decision comes down to would you rather throw away the filter or clean it.

Dry:
Comparable Airflow to oiled Cotton Filters with the same Great Protection. Last for up to 30,000 miles of highway driving. Extend the life of the filter using compressed air.

OIL:
Oiled filters can last forever as long as you properly clean and re-oil it. See maintenance information below.

JLT Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals! For more information check the product page here JLT Air Filter PRE FILTER

MAINTENANCE
To properly clean your filter, we recommend the S&B Precision II Cleaning & Oiling Kit.
*TIP* by purchasing a 2nd air filter you can simply swap filters when it's time to clean it and not be rushed. Clean the first filter and it's ready when it's time to change again.

The computer code on 2005-2010 Mustangs is under the hood on the passenger side located on a silver rectangular box. Code is 3 letters ending with a number. Click here for picture

*This product is NOT CARB (California Air Resource Board) Exempt. It is not for legal sale or use in the state of CA or any other states adopting CA emission standards and require a CA Executive Order (EO) number. Any orders placed for this item with a CA ship to address will be cancelled.

1 Review

  • 5
    GREAT PRODUCT

    Posted by TRAVIS FOWLER on Dec 9th 2019

    VERY HAPPY WITH THE PERFORMANCE FROM THIS PACKAGE

Click to Download PDF
JLT PERFORMANCE LIFETIME SATISFACTION GUARANTEE!
We want you to be a JLT Performance customer for life! Click for Info
JLT Lifetime Warranty Information