JLT Cold Air Intake For 2018-2021 Durango SRT 6.4L Help your HEMI get all the cold air it can eat! Looks great, sounds great with NO TUNE REQUIRED
This kit includes an ABS heat shield that has a opening in the front to grab fresh air from the grille/headlight area and also seals to the hood.
Our air filter is a custom built design made by S&B. It has a built in bell mouth for super smooth and fast air flow as well as huge 1" deep pleats for more surface area than filters that look much bigger.
The intake tube is roto molded plastic with a huge 5" filer opening for superior airflow and NO heat soak like metal tubes.
With a mouth of 4" at the throttle body end, it is ready for any larger throttle bodies that may come in the future.
Standard finish is an OEM looking black textured plastic.
Includes our large ABS plastic heat shield to block engine heat at idle and low speed.
It uses a large area to make sure the filter has tons of cool air and uses the factory fresh air inlet from the bumper to keep temps cool as stock
• JLT Roto Molded Plastic Intake Tube
• Silicone Reducer
• 5x7 S&B Powerstack Air Filter
• ABS Heat Shield
• HD Clamps, all needed hardware
GAINS AND TESTING
18-22 RWHP & 18-22 RWTQ are typical with this kit.
No tuning required
The design, detailed instructions and online video helps make this an easy install (see Instructions & Videos tabs to download / view).
AIR FILTER OPTIONS - OIL OR DRY
We use only the best air filters made by S&B to our specifications.
For years we only used oiled filters, but dry filter technology has been proven and is now a popular option.
Should I choose a Dry Disposable or Cotton Oiled Filter?
Since you are not sacrificing performance with either choice, the decision comes down to would you rather throw away the filter or clean it.
Dry: Comparable airflow to oiled cotton filters with the same great protection.
Last for up to 30,000 miles of highway driving. Extend the life of the filter using compressed air.
Oil: Oiled filters can last forever as long as you properly clean and re-oil it.
Oil filters are available in red or blue and Dry filters are white.
To properly clean your oil filter, we recommend the S&B Precision II Cleaning & Oiling Kit.
*TIP* by purchasing a 2nd air filter you can simply swap filters when it's time to clean it and not be rushed. Clean the first filter and it's ready when it's time to change again.
JLT Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals!
This kit is 50 state legal. CARB E.O. No. D-761-5
This intake comes highly recommended from the Durango SRT community and this doesn't disappoint. I love the intake design of separating the intake filter from the engine heat with the intake shield. Easy installation that took me roughly 20 minutes with the provided instructions. I'm looking forward to lower IAT's and an increase in power. Also would recommend the JLT oil separator. That was my 1st modifications, and it is an absolute must on the 392. Definitely a great combination for my Durango SRT.
Day install by following the video. Looks great. Definitely saw a HP increase on the on board dyno, felt like I had better throttle response and was faster on the “seat of the pants dyno”, especially at higher speeds.
Fits great easy to install
Not only does it's job but looks freaking awesome doing it.
Looks great.. blue filter.. blue pre-filter on my 2018 Durango SRT
Love it. Perfict fit, great video to the tee. Very simple instructions to follow i watched video 1 time and had no issues. Company was awesome to deal with. Got item very quick perfict condition. Thanks kevin f.
Man it sounds awesome!!!! Easy install looks great I looked around for an intake for a while until I saw the intake from JLT it’s pretty bad ass thanks JLT Performance!!!