A JLT solution for your 2015-2019 5.0L F-150
After all of the success of our kits for the 5.0 powered Mustangs we decided to attack the pickup truck market with the same logic. Make a system that's bigger and badder then any other current system available.
JLT's 2015-2019 F-150 5.0L Cold Air Intake is fully computer designed to optimize space and for best fit and finish. Large 4.5" filter inlet with radius-ed end for smooth air flow to the throttle body
Tube measures 4" at the throttle body side in preparation for larger after market throttle bodies.
Retains the bottom half of the stock air box, maintains fresh air feed by doing this! We include a new top half to accept our large filter and tube.
We use only the best air filters made by S&B to our specifications. We love S&B's tapered flange design and Powerstack filtered ends. With a huge 4.5” opening on the tube we needed a huge filter. The result is a monster 4.5x6” filter.
This intake system is NO TUNE REQUIRED.
In our testing we have found gains to be a consistent 10-15RWHP peak, with even more under the curve. See the dyno video below.
The design, detailed instructions and online video (see below) helps make this an easy install (see Instructions & Video tab to download / view).
• JLT Black Textured Intake Tube
• 90 degree Rubber Reducer
• 4.5x6" S&B Powerstack Air Filter
• Heat Shield
• HD Clamps & all needed hardware
To properly clean your oil filter, we recommend the S&B Precision II Cleaning & Oiling Kit.
*TIP* by purchasing a 2nd air filter you can simply swap filters when it's time to clean it and not be rushed. Clean the first filter and it's ready when it's time to change again.
JLT Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals! For more information check the product page here JLT Air Filter PRE FILTER
This kit is street legal in all US states for 2015 and 2016 models, CARB Exempt ID: D-761-2 .
CARB approval is pending for 2017
NOT CARB APPROVED FOR 2018 or 2019
They never disappoint this they're products! Quality and craftsmanship are in ever product line they produce!
INSTALLED YOUR COLD INTAKE KIT ON MY 2018 5.0 F150. EASY INSTALLATION . HARDEST PART WAS GETTING THE FACTORY CONNECTORS UNHOOKED. DID HAVE TO SHORTEN THE SMALL RUBBER EXTENSION HOSE ON THE VACUUM CONNECTION ON THE INTAKE TUBE BY 1/2 AN INCH. WAS PUTTING THE FACTORY VACUUM HOSES IN A BIND. SOUNDS GOOD AND SHOULD BREATHE A LOT BETTER. PLAN ON GETTING YOUR OIL CATCH CAN KIT IN THE NEAR FUTURE . AND A BORLA CATBACK EXHAUST SYSTEM DOWN THE ROAD.
Received my CIA yesterday and had it on in 10 min easiest intake I've ever put on looks good, performs good, and sounds killer! 10/10 would highly recommend
Got my HydroCarbon painted CAI today & it looks AWESOME!
Installed on a 2015 F!50 Lariat Supercab 4x4 w/ 3.31 rear & stock exhaust.
No Tuner or Programmer just factory stock program.
This JLT CAI seems to have woken up a few more ponies in the 5.0L.
Getting on the freeway I went from rolling to get-gone (85++) in a heartbeat. My "Butt-Dyno" sensed the power difference right away.
fyi-Will have to adjust my throttle tip-in as it's way too sensitive, But it was w/ stock system too.
Too early to predict effect on MPG's but I saw no drop in the 11-13 miles I rolled in "drive-it-like-you-stole-it" mode.
Two thumbs up on this product & it was worth the wait for the custom HydroCarbon paint scheme..